Cisco 200-105 Practice Exam Questions

Choose DumpsSchool 200-105 exam questions to get most authentic information about WAN technologies, infrastructure services, and infrastructure maintenance exam topics. These exam questions are relevant to the real exam and enhance your preparation to pass the 200-105 exam.

Try it Latest DumpsSchool 200-105 Exam dumps. Buy Full File here: (691 As Dumps)

Download the DumpsSchool 200-105 braindumps from Google Drive: (FREE VERSION!!!)

Question No. 1

Which statement about STP root bridges is true?

Answer: A

Question No. 2

Refer to the exhibit. On R1 which routing protocol is in use on the route to

Answer: D

Question No. 3

A network administrator needs to configure port security on a switch. Which two statements are true? (Choose two.)

Answer: B, C

Follow these guidelines when configuring port security:

+ Port security can only be configured on static access ports, trunk ports, or 802.1Q tunnel ports. -> A is not correct.

+ A secure port cannot be a dynamic access port.

+ A secure port cannot be a destination port for Switched Port Analyzer (SPAN).

+ A secure port cannot belong to a Fast EtherChannel or Gigabit EtherChannel port group. -> E is not correct

+ You cannot configure static secure or sticky secure MAC addresses on a voice VLAN. -> D is not correct.

+ When you enable port security on an interface that is also configured with a voice VLAN, you must set the maximum allowed secure addresses on the port to at least two.

+ If any type of port security is enabled on the access VLAN, dynamic port security is automatically enabled on the voice VLAN.

+ When a voice VLAN is configured on a secure port that is also configured as a sticky secure port, all addresses seen on the voice VLAN are learned as dynamic secure addresses, and all addresses seen on the access VLAN (to which the port belongs) are learned as sticky secure addresses.

+ The switch does not support port security aging of sticky secure MAC addresses.

+ The protect and restrict options cannot be simultaneously enabled on an interface.

Question No. 4

Which EIGRP for IPv6 command can you enter to view the link-local addresses of the neighbors of a device?

Answer: C

Question No. 5

What are three components that comprise the SNMP framework? (Choose three.)

Answer: A, B, F

Question No. 6

A new switch is being added to the River Campus LAN. You will work to complete this process by first configuring the building_2 switch with an IP address and default gateway. For the switch host address, you should use the last available IP address on the management subnet. In addition, the switch needs to be configured to be in the same VTP domain as the building_1 switch and also needs to be configured as a VTP client. Assume that the IP configuration and VTP configuration on building_1 are complete and correct. The configuration of the router is not accessible for this exercise. You must accomplish the following tasks:

Determine and configure the IP host address of the new switch. Determine and configure the default gateway of the new switch. Determine and configure the correct VTP domain name for the new switch.

Configure the new switch as a VTP client.

Answer: A

Question No. 7

Which protocol is a Cisco proprietary implementation of STP?

Answer: D

Question No. 8

Which IEEE standard does PVST+ use to tunnel information?

Answer: B

Question No. 9

Which value must you configure on a device before EIGRP for IPv6 can start running?

Answer: C

Question No. 10

Refer to the exhibit. You are connected to the router as user Mike.

Which command allows you to see output from the OSPF debug command?

Answer: A

Question No. 11

Which two statement about proxy ARP are true ? (Choose two)

Answer: B, C

Question No. 12

Which encapsulation type is a Frame Relay encapsulation type that is supported by Cisco routers?

Answer: A

Cisco supports two Frame Relay encapsulation types: the Cisco encapsulation and the IETF Frame Relay encapsulation, which is in conformance with RFC 1490 and RFC 2427. The former is often used to connect two Cisco routers while the latter is used to connect a Cisco router to a non-Cisco router. You can test with your Cisco router when typing the command Router(config-if)#encapsulation frame-relay ? on a WAN link.

Note: Three LMI options are supported by Cisco routers are ansi, Cisco, and Q933a. They represent the ANSI Annex D, Cisco, and ITU Q933-A (Annex A) LMI types, respectively.

HDLC is a WAN protocol same as Frame-Relay and PPP so it is not a Frame Relay encapsulation type.

Question No. 13

Refer to the exhibit. HostA cannot ping HostB.

Assuming routing is properly configured, what could be the cause of this problem?

Answer: D

200-105 Dumps Google Drive: (Limited Version!!!)

Related Certification: CCNA Routing & Switching dumps