Pass NS0-181 Exam With Vaild NetApp Certified Storage Installation Engineer, ONTAP NS0-181 Exam Questions

Vendor NetApp
Exam Code NS0-181
Full Exam Name NetApp Certified Storage Installation Engineer, ONTAP
Certification Name NetApp Certified Storage Installation Engineer, ONTAP
Technology ONTAP Cloud

Our NetApp Certified Storage Installation Engineer, ONTAP NS0-181 exam practice software continuously assesses your knowledge and determines when you are ready to pass your NetApp NS0-181 exam. Our ITsecurityexams’s NetApp NS0-181 exam dumps material can assess if there is a gap between your knowledge. We at ITsecurityexams present you latest NetApp NS0-181 exam questions with a focused training module that gets you to pass the NS0-181 certification Exam.

♥ 2018 Valid NS0-181 Exam Questions ♥

NS0-181 exam questions, NS0-181 PDF dumps; NS0-181 exam dumps:: NS0-181 Dumps ( Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate NetApp NS0-181 Exam Questions:

Question: 21

You are preparing to install a new clustered Data ONTAP system.
Which tool prepares all the relevant customer and configuration information?

A. AutoSupport
B. Cluster Config Builder
C. OnCommand System Manager
D. Config Advisor

Answer: C

Explanation:
OnCommand System Manager provides fast, simple configuration and management for NetApp FAS storage systems.
Incorrect: Not A: AutoSupport is used in a system that is already installed. It provides simple, effective, proactive monitoring and management of your storage infrastructure. Not D: Config Advisor is run on already installed systems. It performs configuration validation for new NetApp system installation and improve automation for service delivery for assessments and audits.
Reference: http://www.netapp.com/se/products/management-software/system-manager.aspx

Question: 22

While performing storage failover tests, you notice that a data LIF serving CIFS traffic is not reachable after takeover.
Which three statements are correct in this scenario? (Choose three.)

A. NAS LIFs do not fail over.
B. A front-end switch configuration was missing.
C. An incorrect firewall policy was assigned.
D. No failover policy was assigned.
E. Incorrect ports were in the broadcast domain.

Answer: C,D,E

Question: 23

What happens to the NTP configuration in clustered Data ONTAP 8.3 when a node joins a cluster?

A. A node that joins a cluster has a separate NTP service.
B. A node that joins a cluster automatically adopts the NTP configuration of the cluster.
C. A node that joins a cluster must be manually configured in the NTP.
D. A node that joins a cluster must reboot before running the NTP service.

Answer: B

Explanation:
A node that joins a cluster automatically adopts the NTP configuration of the cluster.
Reference: How to configure and troubleshoot NTP on clustered Data ONTAP 8.2 and later using CLI
https://kb.netapp.com/support/index?page=content&id=1014787

Question: 24

You are assigned to install five DS2246 with twenty-four 400 GB SSDs per shelf to a single node system.
According the NetApp, which statement is correct?

A. You cannot install five SSD shelves to one System.
B. You need at least two stacks.
C. You need at least three stacks.
D. You can put all shelves in one stack.

Answer: D

Explanation:
Up to 10 shelves are supported per stack for the DS2246, so we one stack is enough as we only have five shelves (DS2246s).
Reference: Making the Move from FC to SAS Storage
http://www.netapp.com/as/communities/tech-ontap/tot-fc-sas-1101-as.aspx

Question: 25

Which three types of interface groups are supported on NetApp storage systems? (Choose three.)

A. single mode
B. HA interconnect
C. IPspaces
D. static multimode
E. dynamic multimode

Answer: A,D,E

Explanation:
You can create three different types of interface groups on your storage system: single-mode, static multimode, and dynamic multimode interface groups.
Reference: Types of interface groups
https://library.netapp.com/ecmdocs/ECMP1196907/html/GUID-EFA72201-E035-41E2-AC53-CD81A472B5ED.html

Question: 26

You have just configured the customer’s first SVM with a LIF IP 10.0.0.10/24. The customer’s DNS IP address is 172.16.0.250 and you are unable to ping it from the NetApp storage system, but you are able to ping the gateway and everything else works.
In this scenario what is the problem?

A. You need to have the DNS server on the same subnet as the LIF IP address.
B. You need to add a static gateway to the LIFs routing group.
C. You need to have the customer check the cable.
D. You need to add an IPspace and domain broadcast to the port.

Answer: D

New Updated NS0-181 Exam Questions NS0-181 PDF dumps NS0-181 practice exam dumps: https://www.dumpsschool.com/NS0-181-exam-dumps.html

         

Facebook Comments