Download Free C9010-022 Study Guide With Updated Exam Questions – [Dec-2017 Dumps]

Our IBM AIX V1 C9010-022 exam practice software continuously assesses your knowledge and determines when you are ready to pass your IBM C9010-022 exam. Our ITsecurityexams’s IBM AIX Administration V1 IBM  material can assess if there is a gap between your knowledg. We at ITsecurityexams present you latest IBM C9010-022 exam questions with a focused training module that gets you to pass the C9010-022 certification Exam.

C9010-022 PDF dumps; C9010-022 exam dumps:: https://www.dumpsschool.com/C9010-022-exam-dumps.html (62 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate IBM C9010-022 Dumps Exam Questions and Answers:

Version: 8.0
Question: 21

An administrator needs to determine if system microcode is at the most current level. Which tool will identify current microcode levels, and provide an output file which can be used by the IBM Microcode Discovery Service (MDS) for comparison?

A. FLRT
B. invscout
C. Ismcode
D. prtconf
E. urncode_latest

Answer: B

Question: 22

An administrator was told to reverse the search order of a working DNS lookup. During application testing it was discovered that network resolution was not working for the end users.
Given the following output, what is the most likely cause?

A. The first DNS server is unreachable.
B. The netsvc.conf has the incorrect host lookup order.
C. Incorrect file permissions on the/etc/resolv.conf file.
D. The host is not on the network.

Answer: C

Question: 23

New Updated C9010-022 Exam Questions C9010-022 PDF dumps C9010-022 practice exam dumps: https://www.dumpsschool.com/C9010-022-exam-dumps.html

A host has a single virtual Ethernet adapter (ent0) configured with only a default PVID, and the administrator is trying to determine why it cannot be used to reach any other system on the network. He suspects that it may be caused by a problem in the VLAN configuration.
How would the administrator determine the VLAN for which the adapter was configured?

A. Use the command ‘Isdev -I ent0’ on the host to determine the port VLAN ID.
B. Use the command ‘Isattr-EI ent0’ on the host to determine the port VLAN ID.
C. Look on the HMC to determine which VLAN is configured for the adapter.
D. Examine the Shared Ethernet Adapter on the Virtual I/O Server to determine which VLAN the adapter is using.

Answer: C

Question: 24

How can an administrator disable Role Based Access Control (RBAC) in a WPAR?

A. Run chattr -E -I sys0 -a enhanced_RBAC=false
Reboot the WPAR
B. Run the RBAC wizard and deselect ‘Enable RBAC
Reboot the system
C. Run chdev -I mywpar -a enhanced_RBAC=false
Reboot the Global Environment
D. Run chwpar -a RBAC=false
Reboot the WPAR

Answer: C

Question: 25

After performing a NIM rte install, the administrator noticed that not all filesets are at the correct Technology Level (TL). What action will help the administrator determine why the inconsistent fileset levels were installed?

A. On the NIM server, run an Ippchk to identify if the Software Vital Product Data is valid.
B. On the NIM client, run oslevel command against the TL to identify missing prerequisites.
C. Run instfix command on NIM client to determine what filesets are inconsistent.
D. On the NIM server run the NIM IsIpp command to indentify downlevel filesets contained in the lpp_source.

Answer: D

Question: 26

What is a requirement for Live Partition Mobility?

A. The network and disk must be virtual.
B. The disk must be virtual and a Logical Host Ethernet Adapter (LHEA) for network.
C. The client partition must be connected to a SAN.
D. The client partition must be set up as a ‘Mover Service Partition’.

Answer: A

         

Facebook Comments